Apple Processor Cage and Clips Przewodnik Instalacji Strona 72
- Strona / 117
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
SmartStart Prerequisites
• Microsoft Windows 2008 R2 Server x64 Edition or 2012 is currently running in the system
• 1.0 gigahertz or higher processor
• 1 GB of installed RAM (2 GB recommended)
• CD-ROM or DVD-ROM drive
• 1280 x 1024 or better screen resolution
SmartStart Online Help is supported in the following browser versions:
• Microsoft Internet Explorer 8, 9 and 10
• Mozilla Firefox 14 through 21
After completing the checklist, continue on to “Launching HP 3PAR SmartStart” (page 72).
Launching HP 3PAR SmartStart
Two separate SmartStart setup wizards assist with the set up of the storage system:
• HP 3PAR Service Processor Setup Wizard
• HP 3PAR Storage System Setup Wizard
The setup is sequential and involves the following processes:
• Customizing the communication settings of the SP with the HP 3PAR Service Processor Setup
Wizard
• Setting up the storage system with the HP 3PAR Storage System Setup Wizard
You only need to set up the SP and StoreServ system only once for each new storage system.
Before inserting the HP 3PAR SmartStart CD, the following system requirements must be met.
NOTE: If you cannot locate your CD, call your HP Sales Representative at 1-800-334-5144.
To launch HP 3PAR SmartStart:
1. Insert the HP 3PAR SmartStart CD.
2. Follow the onscreen instructions to launch the application. If the auto-run menu does not appear,
navigate to DVD drive, and double-click the smartstart.exe file.
NOTE: The SmartStart application may take up to 3 minutes to launch.
Continue on to “Launching the HP 3PAR Service Processor Setup Wizard” (page 72) and launch
the setup wizard.
If HP 3PAR SmartStart is unavailable, see “Launching the SP Setup Wizard” (page 113) and learn
how to manually launch the setup wizards.
NOTE: For additional information and help, use the HP 3PAR SmartStart online help (accessible
by pressing F1).
Launching the HP 3PAR Service Processor Setup Wizard
The setup wizard proceeds through the following steps:
• Welcome
• Generate SP ID
• Networking
• Remote Support
• System Support Information
72 Setting Up the Service Processor and Storage System
- Storage Installation Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 1 General Site Planning 6
- Acclimatization 8
- 2 Getting Started 9
- Inspecting the Packaging 10
- Storage System Installation 11
- Disk Drive Numbering 12
- Controller Nodes 13
- I/O Modules 17
- Power Cooling Modules 17
- Service Processor 19
- Power Distribution Units 19
- Important Safety Information 20
- Required Tools 21
- Additional requirements 21
- Configurations 21
- • 1U and 0U configurations 22
- Hardware Installation 23
- Hardware Installation 25 25
- Installing the 1U and 0U PDUs 27
- • 0U bracket installation 28
- 3. Install cage nuts 28
- Securing the Cables 29
- Installation is complete 30
- Unpacking the Cabinet 31
- Positioning the Cabinet 31
- Verify the Cabling 32
- Removing the Brackets 34
- Installing the Rail Kit 35
- Installing the Rail Kit 37 37
- Installing Enclosures 38
- (LFF) disk drive) 40
- Installing a Disk Drive 41
- NoneRound hole 43
- NoneSquare hole 43
- ScrewdriverThreaded hole 43
- • Screwdriver 44
- 7 Cabling the Storage System 50
- Cabling Expansion Cabinets 51
- Cabling the Service Processor 52
- Cabling the Power Strips 53
- Verifying Setup 54
- Verifying LED Status 56
- Figure 37 Disk Drive LEDs 57
- Table 9 PCM LED Descriptions 58
- Node Interconnect Ports 60
- Drive Enclosure LEDs 61
- Figure 42 Front Panel LEDs 62
- Table 11 Front panel LEDs 62
- Figure 43 Rear Panel LEDs 63
- Table 12 Rear panel LEDs 63
- Prerequisites for Using a VSP 64
- Deploying the VSP OVF File 65
- Launching HP 3PAR SmartStart 72
- Generate Service Processor ID 75
- Configure SP Networking 76
- Remote Support 77
- System Support Information 79
- Time and Region 80
- Change Passwords 81
- Applying Settings 83
- Figure 57 Apply Settings 84
- Verify Storage System 88
- Configure Networking 89
- ◦ Subnet Mask 89
- ◦ Gateway 89
- Configuring Time 89
- Figure 65 Configure Time Page 90
- Change Password 91
- Verify Configuration 92
- Progress 92
- Figure 68 Progress Page 93
- Figure 69 Results Page 93
- Contacting HP 95
- HP 3PAR documentation 95
- Typographic conventions 98
- HP 3PAR branding information 98
- 12 Documentation feedback 99
- Figure 74 7000 Series PCM 101
- Figure 75 M6700 Series PCM 102
- Figure 77 SFF Drive Assembly 102
- Figure 79 LFF Drive Assembly 103
- Accessory Kits 104
- Rail Kits 104
- Rail Kits 105 105
- Figure 87 M5 Cage Nut 106
- Adding Disk Drives 110
- Checking Progress 111
- Completing the Upgrade 112
- SmartStart is Unavailable 113
- E Validating Remote Support 114
- G Troubleshooting 117
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.072 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji